The nmc is only necessary for management. Unless quads act differently
than HiperDSPs, you will not need the NMC to function. When I've seen
the question marks, usually TCM or the NMC software is older than the
HiperDSPs/quads.
Since quads are pretty old, I'm going to say you should try to get a
newer version of TCM. Your TCM version should be at least 6.0.23, NMC
should be at least 6.0.9
You may need to static assign the DSPs on the ARCs/Netservers.
-----Original Message-----
From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com
[mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of
Shahrooz Sharghi
Sent: Thursday, July 07, 2005 12:30 PM
To: Discussion relating to the 3Com/US Robotics Total Control
modemsystems.
Subject: Re: [USR-TC] NMC
I put NMC in another slot, even I can ping it and connect to it with TCM
but it show "?" for every slots of chassis even blank slots.
Also I tested it with another NIC but still the same results.
Can I use this chassis without NMC or not? with E1 DSP and without E1
DSP.
Regards
----- Original Message -----
From: Ross <mailto:tech@effingham.net> Cornett
To: Discussion relating to the 3Com/US
<mailto:usr-tc@mailman.xmission.com> Robotics Total Control
modemsystems.
Sent: Thursday, July 07, 2005 9:54 AM
Subject: Re: [USR-TC] NMC
I have never tried to put that NMC in a nother slot, but in your case it
is worth the try.
I would also try another back side card.
After this the chassis must be replaced.
They are cheap.
----- Original Message -----
From: Shahrooz Sharghi <mailto:shahrooz.sharghi@ispcomputers.com>
To: Discussion relating to the <mailto:usr-tc@mailman.xmission.com>
3Com/US Robotics Total Control modemsystems.
Sent: Thursday, July 07, 2005 11:44 AM
Subject: Re: [USR-TC] NMC
in another chassis it works normal!
what do I have to do with my chassis then?
----- Original Message -----
From: Ross <mailto:tech@effingham.net> Cornett
To: Discussion relating to the <mailto:usr-tc@mailman.xmission.com>
3Com/US Robotics Total Control modemsystems.
Sent: Thursday, July 07, 2005 9:31 AM
Subject: Re: [USR-TC] NMC
email me off line. I will assist you if I can.
Sounds like it could be a lights out for the card. Do you have others
to see what they will do?
Other chassis's available to see if the chassis port is bad where the
NMC card plugs in?
Ross
----- Original Message -----
From: Shahrooz Sharghi <mailto:shahrooz.sharghi@ispcomputers.com>
To: Discussion relating to the <mailto:usr-tc@mailman.xmission.com>
3Com/US Robotics Total Control modemsystems.
Sent: Thursday, July 07, 2005 11:21 AM
Subject: Re: [USR-TC] NMC
yes, I have read and write access to it, the keys are factory default
"public" & "private"
also my station running TCM works with other NMC and TCMs.
Thanks a lot
----- Original Message -----
From: Ross <mailto:tech@effingham.net> Cornett
To: Discussion relating to the <mailto:usr-tc@mailman.xmission.com>
3Com/US Robotics Total Control modemsystems.
Sent: Thursday, July 07, 2005 9:03 AM
Subject: Re: [USR-TC] NMC
are you sure you have read and write capability to the chassis?
SNMP could be the issue here.
Just checking.
----- Original Message -----
From: Shahrooz <mailto:shahrooz.sharghi@ispcomputers.com> Sharghi
To: Discussion relating to <mailto:usr-tc@mailman.xmission.com> the
3Com/US Robotics Total Control modemsystems.
Sent: Thursday, July 07, 2005 10:27 AM
Subject: [USR-TC] NMC
I have to add that my NMC even doesn't detect netserver card (it detects
nothing!). Is it a bad card? how can I repair it?
Thanks
Shahrooz
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_____
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
I have a NMC card don't detect any quad analog/digital modem cards and E1 hiper dsp, it's software code is 6.1.7
How can I upgrade that? I don't have any code for NMC card.
Please guide me.
Best Regards
Shahrooz Sharghi
