August 2004 - USR-TC - mailman.xmission.com

Want to Buy: Qty 3 V.34 Analog/Digital NACs
by Russell Newberry 17 Aug '04

17 Aug '04

I need Qty 3 Analog/Digital Modem NACs (software 5.10.9 preferred, if available). Anybody have spares? I may be looking to pick up several more in the next few weeks as well, with any software version. Let me know whatcha got! Thanks, Russell Newberry ==================== Maxis Technologies, Inc 433 W. Wilshire Blvd. Ste 2B Oklahoma City, OK 73116 Voice: 1-800-79-MAXIS Int'l: 1-405-842-3331 FAX: 1-405-841-7882 find us on the web at www.maxistech.net email to: russell(a)maxistech.net AOL IM "RUSSELLatMAXIS"

1 0

re:Cannot Logon to TC1000
by jmarquez＠fuse.net 17 Aug '04

17 Aug '04

I think I may have a solution.... The TC1000 with V4.1.11 will accept chap with md4 or md5 hash, So the Cisco, Nortel and Windows all work without problems. The TC1000 with V5.3.3 works only with CHAP MD5. The Cisco and Windows can check with MD5, but the Nortel ARN works only with MD4. Am I on the right track ? Is there any way to get V5.3.3 to accept MD4 hash? What version of ARC code would I need to downgrade to get MD4 Support? Thanks -Jim >I have a TC1000 with ARC 5.3.3/non-encr software. > >I have configured the card to use chap. Here is my problem. > >I can use a Cisco 1700 router to logon to the TC, I can use Windows to dial >into the TC, but when I try to use a Nortel ARN to logon, I get a chap >failure mismatch. > >I have another TC1000 with V4.1.11 that all can dial into without problems. I >have tried to duplicate the configuration, but I must be missing something. > >Any suggestions? >Thanks >-Jim

2 1

NMC sends out cooling fan trap, but no bad fan's found? Red status on NMC?
by de Vries, Christiaan 17 Aug '04

17 Aug '04

Hi list, Just wondered if anybody has experience with the following and could tell me how to possible resolve this problem; - NMC sends out traps that one of the fantray's fan's is broken. - NMC HUB status is 'RED' - Checking the fantray, everything seems to work normally, temp. is around 24 degrees Celsius. Any clues as to what could be wrong? This is a 130AMP Chassis btw. :/u/support> snmpinfo -m dump -h 10.92.0.1 nmcstatredled 1.3.6.1.4.1.429.1.2.2.12.0 = 3 (Code 3: Fan Failure) :/u/support> 10.92.0.1 uchasPowerSupplyOperStatus 1.3.6.1.4.1.429.1.1.4.1.1.3.1 = 3 1.3.6.1.4.1.429.1.1.4.1.1.3.2 = 3 :/u/support> -h 10.92.0.1 nmcStatTemperature nmcStatTemperature.0 = 24 Run/Fail : Solid Green Hub Status: Solid Red Thanks! Christiaan

1 0

Explaination of version numbers
by jmarquez＠fuse.net 16 Aug '04

16 Aug '04

I have a question about the version numbers on a HiperArc card. What is the difference between vx.x.x and vx.x.x/non-encr ? Does one have VPN software and the other not? Thanks -Jim BTW please see my other post for CHAP problems.... http://mailman.xmission.com/pipermail/usr-tc/2004-August/008536.html

1 0

RE: [USR-TC] Problem Figuring out E1 DSP's
by Joel - Fox Computers 16 Aug '04

16 Aug '04

Oh yeah - that was it. Just tested and problem solved. Thanks again. Joel -----Original Message----- From: Joel - Fox Computers Sent: Monday, August 16, 2004 9:25 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] Problem Figuring out E1 DSP's Todd, I never even thought about checking the snmp on it, just assumed public and private. DOH! Thanks, Joel -----Original Message----- From: Todd Bertolozzi [mailto:berto@core.com] Sent: Monday, August 16, 2004 7:42 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Problem Figuring out E1 DSP's Sounds like you're using the read string instead of the write community string. Todd ----- Original Message ----- From: "Joel - Fox Computers" <jfox(a)foxcomputers.com> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc(a)mailman.xmission.com> Sent: Sunday, August 15, 2004 11:39 PM Subject: [USR-TC] Problem Figuring out E1 DSP's > > I got a chassis with 7 E1 DSP's in it, a Hiper ARC, and a Hiper NMC. At first, TCM wouldn't even let me see settings on the DSP's. Someone here on the list suggested updating the code on the NMC. So I loaded 8.6.3 on it. Then I could see the trunk settings. > > NOW... if I go to Configure->Actions/Commands, it won't let me run any commands on the DSP's. I can't even force a hardware reset. After I try to execute any command, in the status area at the bottom of the window, it displays the Device(s), pauses for a few seconds, then just says "No Command" under the Command column and nothing happens. > > Any suggestions? > > Thanks, > > Joel > > > > -----Original Message----- > From: David E. Smith [mailto:dave@mvn.net] > Sent: Friday, August 06, 2004 11:50 AM > To: Adam Barnhill > Cc: usr-tc(a)mailman.xmission.com > Subject: RE: [USR-TC] Help: Dropping packets for not-in-use IPs > > > On 6 Aug 2004 at 11:40, Adam Barnhill wrote: > > > HiPer>>enable ip send_host_unreach_for_pool > > THIS is why I love mailing lists. Thanks! > > (If the semo in semo.net is for Southeast Missouri, I owe you a beer next time > I'm in Cape Girardeau.) > > David Smith > MVN.net > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] Problem Figuring out E1 DSP's
by Joel - Fox Computers 16 Aug '04

16 Aug '04

Todd, I never even thought about checking the snmp on it, just assumed public and private. DOH! Thanks, Joel -----Original Message----- From: Todd Bertolozzi [mailto:berto@core.com] Sent: Monday, August 16, 2004 7:42 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Problem Figuring out E1 DSP's Sounds like you're using the read string instead of the write community string. Todd ----- Original Message ----- From: "Joel - Fox Computers" <jfox(a)foxcomputers.com> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc(a)mailman.xmission.com> Sent: Sunday, August 15, 2004 11:39 PM Subject: [USR-TC] Problem Figuring out E1 DSP's > > I got a chassis with 7 E1 DSP's in it, a Hiper ARC, and a Hiper NMC. At first, TCM wouldn't even let me see settings on the DSP's. Someone here on the list suggested updating the code on the NMC. So I loaded 8.6.3 on it. Then I could see the trunk settings. > > NOW... if I go to Configure->Actions/Commands, it won't let me run any commands on the DSP's. I can't even force a hardware reset. After I try to execute any command, in the status area at the bottom of the window, it displays the Device(s), pauses for a few seconds, then just says "No Command" under the Command column and nothing happens. > > Any suggestions? > > Thanks, > > Joel > > > > -----Original Message----- > From: David E. Smith [mailto:dave@mvn.net] > Sent: Friday, August 06, 2004 11:50 AM > To: Adam Barnhill > Cc: usr-tc(a)mailman.xmission.com > Subject: RE: [USR-TC] Help: Dropping packets for not-in-use IPs > > > On 6 Aug 2004 at 11:40, Adam Barnhill wrote: > > > HiPer>>enable ip send_host_unreach_for_pool > > THIS is why I love mailing lists. Thanks! > > (If the semo in semo.net is for Southeast Missouri, I owe you a beer next time > I'm in Cape Girardeau.) > > David Smith > MVN.net > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Problem Figuring out E1 DSP's
by Joel - Fox Computers 16 Aug '04

16 Aug '04

I got a chassis with 7 E1 DSP's in it, a Hiper ARC, and a Hiper NMC. At first, TCM wouldn't even let me see settings on the DSP's. Someone here on the list suggested updating the code on the NMC. So I loaded 8.6.3 on it. Then I could see the trunk settings. NOW... if I go to Configure->Actions/Commands, it won't let me run any commands on the DSP's. I can't even force a hardware reset. After I try to execute any command, in the status area at the bottom of the window, it displays the Device(s), pauses for a few seconds, then just says "No Command" under the Command column and nothing happens. Any suggestions? Thanks, Joel -----Original Message----- From: David E. Smith [mailto:dave@mvn.net] Sent: Friday, August 06, 2004 11:50 AM To: Adam Barnhill Cc: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Help: Dropping packets for not-in-use IPs On 6 Aug 2004 at 11:40, Adam Barnhill wrote: > HiPer>>enable ip send_host_unreach_for_pool THIS is why I love mailing lists. Thanks! (If the semo in semo.net is for Southeast Missouri, I owe you a beer next time I'm in Cape Girardeau.) David Smith MVN.net _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

Cannot logon to TC1000
by jmarquez＠fuse.net 13 Aug '04

13 Aug '04

I have a TC1000 with ARC 5.3.3/non-encr software. I have configured the card to use chap. Here is my problem. I can use a Cisco 1700 router to logon to the TC, I can use Windows to dial into the TC, but when I try to use a Nortel ARN to logon, I get a chap failure mismatch. I have another TC1000 with V4.1.11 that all can dial into without problems. I have tried to duplicate the configuration, but I must be missing something. Any suggestions? Thanks -Jim

1 0

Using Ascend-Data-Filter to block port 25
by Wayne 11 Aug '04

11 Aug '04

Hello All, Has anyone used a Ascend-Data-Filter to filter port 25 connection. I have setup my radius server to send radius reply messages with the following data filter. Ascend-Data-Filter = "ip in forward tcp est",Ascend-Data-Filter = "ip in forward dstip 208.6.238.0/24",Ascend-Data-Filter = "ip in drop tcp dstport = 25",Ascend-Data-Filter = "ip in forward" This works fine on my cisco routers but doesn't work on my Total Control. I set radius ATTRIBUTE_STYLE ascend but this didn't do anything for me. Could someone clue me in on what else I need to change on the Total Control ? Thanks Wayne

2 3

Looking for Hiper DSP E1 sets
by Russell Newberry 10 Aug '04

10 Aug '04

Hi Guys, I'm looking to pick up qty 14 Hiper DSP E1 Sets. Anybody looking to sell? Let me know whatcha got! Also, I have the following for sale: Qty 1 333 NMC II set Qty 2 Hiper NMC sets Qty 10 96-port Multispan Sets Looking for offers on the above. Thanks, Russell Newberry ==================== Maxis Technologies, Inc 433 W. Wilshire Blvd. Ste 2B Oklahoma City, OK 73116 Voice: 1-800-79-MAXIS Int'l: 1-405-842-3331 FAX: 1-405-841-7882 find us on the web at www.maxistech.net email to: russell(a)maxistech.net AOL IM "RUSSELLatMAXIS"

1 0