April 2003 - USR-TC - mailman.xmission.com

Hidden commands
by alex 12 Oct '04

12 Oct '04

What does command _set memory threshold critical/high/low do? For what is this threshold used? P.S. (for them who dont know): to show hidden commands type "_reveal commands" and then type "?".

3 4

*MORE INFO* RE: [USR-TC] Urgent Problem - Any Ideas? Major WTF here.
by Joel - Fox Computers 21 Oct '03

21 Oct '03

Yep, I was working that late - Wish this was one of Shannan's boxes. This morning, the ARC on this unit rebooted again. and absolutely every B-channel was local out-of-service. At the reboot, the ARC said this: EXCEPTION 0300 CRASH DUMP: GPRs: R0: 0x0065EC88 R1: 0x07F55E88 R2: 0x000F3200 R3: 0x41820114 R4: 0x07F55F68 R5: 0x00000003 R6: 0x00000006 R7: 0x0000000F R8: 0x00000000 R9: 0x00000000 R10: 0x0000000F R11: 0x00000006 R12: 0x0000003C R13: 0x000FD248 R14: 0x0099D9FC R15: 0x0099D9E0 R16: 0x0099D9E8 R17: 0x0099D9D4 R18: 0x0099D9DC R19: 0x0099D9EC R20: 0xFFFFFEFF R21: 0x00CC5FF0 R22: 0x00306F34 R23: 0x00C10220 R24: 0x00000000 R25: 0x014D9364 R26: 0x01E4F2B4 R27: 0x00000000 R28: 0x009D9070 R29: 0x00000000 R30: 0x000000FF R31: 0x01342E44 SPRs: CR: 0x20000400 XER: 0x20000000 LR: 0x0065EC88 CTR: 0x005171BC SRR0: 0x00661FC0 SRR1: 0x00009030 DSISR: 0x40000000 DAR: 0x41820157 DMISS: 0x41820150 DCMP: 0x80000006 HASH1: 0x00010800 HASH2: 0x0001F7C0 IMISS: 0x00000000 ICMP: 0x00000000 RPA: 0x00000000 IABR: 0x00000000 82660 Registers: Err Status 1: 0x00, Err Status 2: 0x00, CPU Err: 0x14, PCI Err: 0x06 CPU/PCI Addr: 0x00061EFC, Sys Error Addr: 0x0006E960 Call Stack: 0x00661FC0 (Exception return address - SRR0) 0x0065EC88 0x0063B3F8 0x00638594 0x00306F88 0x007F6BB4 0x007F6E74 0x002008D4 0x0020024C 0x0020009C 0x000A95A0 The first 2000 bytes in the Stack follows 0x83C10010 0x7C0803A6 0x8001001C 0x906CC040 0x38600001 0x3D80009A 0x48000010 0x38600000 0x4182000C 0x2C030000 0x90610008 0x483E4875 0x38A00040 0x8084BFC0 0x3C80009A 0x387F0000 0x907E0004 0x483F5CC1 0x9143001C 0xB17E0000 0x614A4354 0x816B19C8 0x3D404143 0x83C30008 0x3D600089 0x4800005C 0x38600000 0x4182000C 0x2C0C0000 0x81810008 0x41820010 0x7C7F1B79 0x483F1605 0x9001001C 0x38A00040 0x93E10014 0x60845030 0x38C10008 0x93C10010 0x38600014 0x3C805544 0x9421FFE8 0x7C0802A6 0x4E800020 0x38210040 0x7C0803A6 0xBB010020 0x80010044 0x7D99C12E 0x39800000 0x4182000C 0x2C0B0000 0x7D79C02E 0x3B393514 0x3F200089 0x4181FF28 0x2C0C0000 0x81990010 0x483EA8ED 0x387E0000 0x483EA8F5 0x807E0008 0x483F1801 0x38800000 0x807F0000 0x40820018 0x2C0B0000 0x897F0004 0x83FE0008 0x4BFFC5E1 0x38A00002 0x7C6C5A14 0x81830008 0x389F0000 0x8163000C 0x4082001C 0x7C1D6000 0x83AB0004 0x816B0000 0x618C6104 0x817E0008 0x3D80554D 0x994C024A 0x394A00FF 0x894C024A 0x7D8C5A14 0x8163000C 0x81830008 0x41820050 0x7C7F1B79 0x483FEF9D 0x809D0000 0x83AA0008 0x814A0000 0x387C0000 0x81430008 0x996C0004 0x396B00FF 0x896C0004 0x81830008 0x418200D4 0x2C030000 0x408200DC 0x2C0A0000 0x8141000C 0x3BC30000 0x483E609D 0x38800000 0x38790000 0x38A1000C 0x3B3E0000 0x3B9C64A0 0x3F8000CE 0x408100EC 0x2C0A0000 0x815E0010 0x7FCC5A14 0x398C6550 0x3D8000CE 0x1D6B0024 0x572B063E 0x4180FFCC 0x2C1C0100 0x3B9C0001 0x4BFFF40D 0x387F0000 0x38810008 0x9B810008 0x40820014 0x7C0BD800 0x7D6BD838 0x7FBB6030 0x7D7E58AE 0x578C077E 0x578BEEFE 0x3BBC0000 0x7FC96214 0x3BFB0000 0x39292A9C 0x3B800001 0x3D200089 0x1D9B0530 0x573B063E 0x4181FFA0 0x7C0AF840 0x815D02DC 0x3BFF0001 0x3BDE0138 0x7D3CC12E 0x39200000 0x483F1961 0x38800000 0x7C7CC02E 0x483F7F15 0x38800020 0x41820020 0x2C030000 0x7C7CC02E 0x7F8C5A14 0x8163000C 0x81830008 0x41820038 0x2C030000 0x483FF0C1 0x387A0000 0x808C00F8 0x7D8CF214 0x819B0000 0x3B7BD150 0x3B5A64A0 0x3BBC0000 0x3BDF0000 0x3F60009A 0x3F4000CE 0x41820080 0x2C0B0000 0x817C02DC 0x3BE00000 0x4800020C 0x4181FF74 0x7C0AD840 0x815D02DC 0x3B7B0001 0x3BFF0138 0x48000711 0x91410014 0xB161001A 0x7D4A602E 0x39600000 0x91610010 0x38610010 0x1D9E001C 0xB1810018 0x7D5D5214 0x1D4A0054 0x816B00F8 0x572A063E 0x7D6BFA14 0x817A0000 0x572C063E 0x91840028 0x39800000 0x4082004C 0x2C0A0000 0x7D44C02E 0x7C8C5A14 0x8163000C 0x81830008 0x41820064 0x2C030000 0x483FF17D 0x387C0000 0x808C00F8 0x7D8CFA14 0x819A0000 0x3B5AD BOOT PROM Version 1.16 (Built on June 9th, 1998 at 12:24:24) Loading kernel ... OK -----Original Message----- From: S.Young [mailto:sky1@airmail.net] Sent: Saturday, April 26, 2003 1:59 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Urgent Problem - Any Ideas? Major WTF here. Joel. You gotta be kidding me. My e-mail says it's 11:57 P.M. Please tell me you aren't still messing around with Total Control boxes at this hour. (Actually, it's 1:45 A.M. here in Dallas, I'm up feeding junior (6-month old son) ). The internet will survive, take a break!! If you need a spare/benchmark unit out there, let me know and I'll get one going your way. All I ask is that you pick up the freight on this "beast". You must not have got that unit from us, we never have any problems with the units WE send out. Go to Bed! Shannan Young SouthWest Data Technology, Inc. sky1(a)airmail.net www.swdt.com 972-739-7010 972-739-7013 (Fax) ----- Original Message ----- From: Joel - <mailto:jfox@foxcomputers.com> Fox Computers To: Discussion relating to the 3Com/US <mailto:usr-tc@mailman.xmission.com> Robotics Total Control modemsystems. Sent: Friday, April 25, 2003 11:54 PM Subject: RE: [USR-TC] Urgent Problem - Any Ideas? Major WTF here. Too funny - but thanks for the vote of confidence - this one has me stumped - but I'm certain I don't have 8 bad DSP's, that I'm sure of. -----Original Message----- From: matthew(a)the-spa.com [mailto:matthew@the-spa.com] Sent: Friday, April 25, 2003 11:23 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Urgent Problem - Any Ideas? Major WTF here. i had something similar but it was only on one card, and that card would show funny lights when you booted it up from day one and it just turned out to be a bad card. you have a whole bunch of cards all doing this, so i don't know what it could be. if i had this i would call you and just have you figure it out :) matthew ---- Original Message ---- From: jfox(a)foxcomputers.com To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Urgent Problem - Any Ideas? Major WTF here. Date: Fri, 25 Apr 2003 22:06:49 -0500 > >Ok - here's the story. > >Just set up a chassis that has 3.5.109 on the DSP's, 5.3.110 on the >ARC, 8.6.3 on the NMC. Running 8 PRI's the telco says are configured >on a DMS100. > >Loaded factory defaults on everything and configured it up. The unit >started taking calls, everything looked good. Got up to about 100 >users on. Walked away from it. > >After about 2 hours, came back to it, and no callers. in session >monitor in TCM, the (most) B-channels on all 8 PRI's showed "Local >out of service". All except on the 8th PRI, one caller remained >connected. I also noticed the D-ALM light intermittently going red >on some of the PRI's. As I watched, slowly the B-channels all >started changing to "Idle" and "in service". But not all at once, on >any give PRI, I'd have the D up, and 19 of the B's, with any 4 of the >B's still "local out of service". > >Talked to the Telco, they said everything was up and the B-channels >were taken down on our end. > >At this time, I noticed a message on the console port of the ARC that >said: >At 17:48:04, Facility "GWC Modem Driver", Level "CRITICAL":: >callline->callstate = 9 > >Now, I've seen similar behavior when the switch type was not correct. > Without help from the Telco, I tried changing the switch type on the >trunk settings to NI2 (which turned out to be the correct answer last >time something like this happened). Then rebooted all of the DSP's. > >Once I did this - the D-channels stopped dropping and all the >B-channels were back, callers started getting on again. Looked good. > >2 1/2 hours later, checked on the box. Only 3 DSP's had callers. At >this point, noticed on the terminal, that the ARC had rebooted. >Scrolling up in HyperTerminal revealed that some type of exception >had happened, and the ARC had rebooted. (Turned on text capture on >HyperTerminal at this point). > >15 minutes later, all of the callers disappeared. Checked, and all >B-channels were down. Thinking it might be ARC related, I gave the >ARC a reboot command. Immediately on giving it the reboot - this is >what I saw: > >HiPer>> reboot >You have requested to Reboot the system >Please confirm the request.(No/Yes):y > >Rebooting.... >At 21:07:44, Facility "Configurator", Level "INFORMATION":: Received >a CFG_SERVICE_CLOSED_MSG message. Administrator Network Service >telnetd has been disabled. >At 21:07:44, Facility "GWC Modem Driver", Level "CRITICAL":: >callline->callstate = 1 > >At 21:07:44, Facility "GWC Modem Driver", Level "CRITICAL":: >callline->callstate = 1 > >At 21:07:44, Facility "GWC Modem Driver", Level "CRITICAL":: >callline->callstate = 1 > > > >Immediately after this, I pulled up session monitor on one of the >DSPs. And about 10 seconds later all of the B-channels changed from >"local out of service" to "in service". > >Once the ARC rebooted, getting fast-busy's dialing in. Checked other >DSP's and they were all again "local out of service". > >On the 1st DSP, did an Actions/Commands->Software->Restore and all of >it's B-channels went "in-service". > >Did a restore on the rest of the DSP's, and all the B-channels went >in-service everywhere, but still getting fast-busy. Gave it about 3 >minutes, still fast-busy. > >On a hunch - did a Hardware reset on the First 4 DSP's. Almost >instantly, the 7th and 8th DSP's started taking calls. >(?!)Interestingly though - I still get a fast busy when I dial it >myself, and the first DSP just got two utilization lights lit and >then rebooted itself. Shortly thereafter, most of the B-channels >went out of service again and the callers dropped off. But the ARC >isn't giving any errors at the console port at this moment. > >So, for lack of any ability to get and keep users connected, I just >reset all the DSP's to the DMS100 switch type, and rebooted the >cards. Immediately, callers started connecting. Session Monitor >shows EVERY B-channel is up. But for how long? > >Is the switch-type so far wrong that it just can't function >continuously? Is the ARC fried? Is this chassis haunted? > >Nothing I can say but: WTF? > >Anyone have any ideas? > >Thanks, > >Joel > > > > > > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

4 4

Throughput half the connect speed.
by tarvid 01 Oct '03

01 Oct '03

Anyone have an explanation how throughput as measured by bing and bandwidth.com being half or less the connect speed? One box recently has 50,333 connects and 20kb downloads. Jim Tarvid

7 9

Total Control Chassis (Weekly Posting)
by sky1 15 May '03

15 May '03

Have 21 left of the fully populated chassis. $2750.00 each All configured as follows: (14) Hiper DSP card sets (2) Hiper ARC 128 Mb version (1) Hiper NMC (2) 130 Amp AC power supplies (1) Blue labeled chassis w/ integrated fan assembly --Excellent condition, Six (6) Month warranty.....$2750.00 each If you need 'em, let me know. Thanks, Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

2 2

Test
by sky1 09 May '03

09 May '03

SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

2 1

ISDN CPE Question
by Joel - Fox Computers 07 May '03

07 May '03

Got the following email earlier and didn't have an answer. Anyone here have a good suggestion? Quick question, Do you know of a good working customer end modem to use on a ISDN line to dial into TC100 (HiPerARC, HiPerDSP,HiPerNMC) gear? I hear that Verizon is going to offer a test ISDN flat rate service to selected 'rural' comunities in my service area (Northern NH) to satisfy political presure to provide 'Broadband' services where no other affordable High Speed conectivity is available. I'd like to be able to offer aN install package with CPE to take advantage of this "_new_" ;-) product in the three towns they (Verizon) are going to run this test case in.

4 3

Welcome Message
by Anil 07 May '03

07 May '03

Hi, How can i set welcome message globally to all users conecting to TC 1000 on both quad modem and 30 Channel High Density Modem. Regards Anil

2 1

RE: (usr-tc) NMC not responding
by Mark E. Levy 06 May '03

06 May '03

I;ve had this happen a few times. Just reboot the NMC card by sliding it out if the chassis or via the console interface and it will be well again (until next time). Rebooting the NMC won't affect active users sessions. --------------------------------------------------------------------- Mark E. Levy, President FSInet, Inc. | System Management Associates, Inc. 800-827-6085 x202 | 847-291-1550 x202 847-753-6832 fax | 847-291-3866 fax www.fsi.net | www.sysman-inc.com mark(a)fsi.net | levy(a)sysman-inc.com --------------------------------------------------------------------- > -----Original Message----- > From: Jeff Mcadams [mailto:jeffm@iglou.com] > Sent: Friday, June 08, 2001 9:51 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) NMC not responding > > > Also sprach Kirk Mitchell > > My NMC recently stopped responding to SNMP queries, etc and I'm > >unable to access it via TCM. It has, however, not seemed to affect > >anything as far as dial-up, routing, etc. Other than the fact that I > >can't run MRTG against it or the badmodems.pl script, there's no > >indication that it's having problems. > > Not surprising. The NMC does not have anything to do with the routine > actions of taking and handling calls...it is what it says it > is...purely > a management card. You can totally remove the NMC and not lose any of > the actual *production* functionality of the chassis. > > > Has the card gone bad...need replaced, lost something in part of > >config? How do I go about finding/fixing the problem? > > Proly just needs a reboot, or possibly a reconfig...I've had > a few lose > some of the config (including IP addresses and stuff), and a reconfig > from console (takes me about 30 seconds these days) gets them > fully back > up and running (sucks if its a remote city though). > -- > Jeff McAdams Email: jeffm(a)iglou.com > Head Network Administrator Voice: (502) 966-3848 > IgLou Internet Services (800) 436-4456 > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

RE: [USR-TC] Re: confirm 7ed7b16a7d92cddc1e800ca5be2ccde8ecc3420c
by Joel - Fox Computers 01 May '03

01 May '03

I got that too - must have been something wrong over night -----Original Message----- From: Chincogan Network Services Lists [mailto:lists@chincogan.net.au] Sent: Wednesday, April 30, 2003 4:29 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Re: confirm 7ed7b16a7d92cddc1e800ca5be2ccde8ecc3420c On Wed, 30 Apr 2003 07:10:32 -0600 usr-tc-request(a)mailman.xmission.com wrote: > Your membership in the mailing list USR-TC has been disabled due to > excessive bounces The last bounce received from you was dated > 30-Apr-2003. You will not get any more messages from this list until > you re-enable your membership. You will receive 3 more reminders like > this before your membership in the list is deleted. > > To re-enable your membership, you can simply respond to this message > (leaving the Subject: line intact), or visit the confirmation page at > > http://mailman.xmission.com/cgi-bin/mailman/confirm/usr-tc/7ed7b16a7d92cddc… > > > You can also visit your membership page at > > http://mailman.xmission.com/cgi-bin/mailman/options/usr-tc/lists%40chincoga… > > > On your membership page, you can change various delivery options such > as your email address and whether you get digests or not. As a > reminder, your membership password is > > niosmu > > If you have any questions or problems, you can contact the list owner > at > > usr-tc-owner(a)mailman.xmission.com > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

5 5

RE: [USR-TC] 50k connect 30k download
by Joel - Fox Computers 01 May '03

01 May '03

Depends on where you're doing the test from. If you're testing to any site on the internet, 40K is normal, 30K isn't unusual, without compression. -----Original Message----- From: tarvid [mailto:tarvid@ls.net] Sent: Wednesday, April 30, 2003 4:32 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: [USR-TC] 50k connect 30k download On Wednesday 30 April 2003 05:28 pm, Joel - Fox Computers wrote: > I got that too - must have been something wrong over night > Me too and I changed email address on the list. My question is if a 50k connect yields a 30k download (and less), it that RAS or telco? _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1