October 2003 - USR-TC - mailman.xmission.com

Hidden commands
by alex 12 Oct '04

12 Oct '04

What does command _set memory threshold critical/high/low do? For what is this threshold used? P.S. (for them who dont know): to show hidden commands type "_reveal commands" and then type "?".

3 4

[USR-TC] Trying To Prevent Virus Spread Need Help With Filters ASAP!
by Travis M. Best 08 May '04

08 May '04

Can Someone Provide Me With Detailed Instructions On How To Block Port 135 Both Incoming And Outgoing On My Chassis Including The Command To Exit Out Of The Editor Please Help Triyng To Prevent A Virus From Spreading Thanks Travis M. Best sysadmin(a)sunqwest.net -- This message has been scanned for viruses and dangerous content by SunQwest MailScanner, and is believed to be clean.

2 1

MP/16 Managed new sdl = ?
by Sergei Markelov 15 Dec '03

15 Dec '03

We have USR Total Control MP/16 Managed modem pool (sku# 001268-0). According to the page 100-102 of manual from http://support.3com.com/docs/rapd/mp16vsnm.pdf this device can work with leased line only on speed 19200 (v.34 must be disabled). I guess this is a software problem since MP/16 non-managed (sku# 000939-0) had the same restriction 19200 with old sdl's, but can use V.34 and do 33600 on leased lines with new sdl's (and standart USR Courier also can use V.34 on leased lines since 1996). Maybe this can be solved by loading new SDL - our pool is very old (the answer on ATI7 command is below). It seems that sdl's for MP/16 non-managed cannot be used in this case. Does anybody have newer SDL's for MP/16 Managed ? ati7 Configuration Profile... Product type US/Canada Rackmount Options HST,V32bis,Terbo,V.FC,V34+ Fax Options Class 1/Class 2.0 Clock Freq 20.16Mhz Eprom 256k Ram 32k Supervisor date 03/13/96 DSP date 11/29/95 Supervisor rev 2.0.8 DSP rev 1.2.7 OK Thank you! Sergei Markelov technical director Moscow Center for Continuous Mathematical Education www.mccme.ru markelov(a)mccme.ru +7-095-2410500phone +7-095-2916501fax

2 1

RE: [USR-TC] HiPer ARC & TCM!!!!
by Kirti S. Bajwa 10 Dec '03

10 Dec '03

Wayne: Please also answer configuration of HiPer DSP. I have configured it only using TCM (no CLI). Does it work or HiPer DSP should be configured from CLI? Thanks. Kirt -----Original Message----- From: Wayne Barber [mailto:barberw@tidewater.net] Sent: Monday, September 22, 2003 11:39 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] HiPer ARC & TCM!!!! TCM was never meant to configure or control the ARC. It's only use with the ARC is to display hardware and software versions. The results you are seeing are normal. HARM, IMHO, was never a reliable product. You are better off using CLI to program the ARC. On 20 Sep 2003 at 17:36, Kirti S. Bajwa wrote: > Hello List: > > I finally figured out how to configure HiPer ARC using CLI & HARM. However, > when I display ARC in TCM, none of the settings are showing! Can someone > explain why? > > Thanks. > > Kirt Bajwa > TIB Computer Systems > Mountain City, TN 37683 > Tel: (423) 727-3001 > eMail: kbajwa(a)tib.com <mailto:kbajwa@tib.com> > > Wayne Barber Coastal Telco Services _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

4 3

Factory Default of Hiper ARC
by Ahamed Bauani 11 Nov '03

11 Nov '03

Hello All I have a grate problem. Just few days ago our USR-TC is working find. But when we were going to change some configuration like IP address,IP Pool etc it start problem. My current problem is I cann't access to Hiper ARC by consol or from network (Telnet). When we reboot the TC with consol connected it's only showing : Booting*...* Loading Kernel....OK Then no other messages on consol. I tryied to telnet it over network but it didn't respond, ping it, result same. I am sure that this Hiper ARC card is OK, but some how I removed the IP of this and disable administration via consol. My current position is " I HAVE NO ACCESS TO THIS CARD!!" Think only it's be possible if somehow I can get it back to factory default. Do you have any idea how to set it factory default? Or any other suggation... really in a bad position. please help. Thanks in advance; Ahamed Bauani. __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software http://sitebuilder.yahoo.com

5 5

ip routing
by Andre Dalle 30 Oct '03

30 Oct '03

I have 2 class-C subnets - 137, 141. eth:1 is setup on subnet-137, and modems assigned addresses from 137 work fine. Can the Hiper route packets from modems assigned 141 addresses through the eth:1 interface? Or do I have to setup eth:2 on subnet-141? -- Andre Dalle [adalle(a)ncf.ca] Systems Administrator, National Capital Freenet [http://www.ncf.ca]

3 2

Dual PRI Card
by Jim Johnson 30 Oct '03

30 Oct '03

We have a T1 Nic for a Dual PRI Nac. I seem to recall that the T1 Nic can be turned into the E1 Nic by uploading the proper firmware. Is that true? Thanks, Jim

2 2

Filters on HiperARC
by Nyagitari Bosire 29 Oct '03

29 Oct '03

Hallos, Asking for anyone with knowledge of where I can read more on deploying filters to forward me the links. Any assistance will be highly appreciated -- Regards, Nyagitari Bosire,

1 0

Missing Radius STOP records
by Andre Dalle 27 Oct '03

27 Oct '03

We've noticed that we have been getting some START records on the same port with no STOP in between. Verifying the syslog shows the same - call connected as normal, then another call connected on same port. We have 10 pri connected on a unit with 2 hiper router cards. -- Andre Dalle [adalle(a)ncf.ca] Systems Administrator, National Capital Freenet [http://www.ncf.ca]

1 0

Default IP for Netserver 16 ???
by RomaCh 27 Oct '03

27 Oct '03

Yo can used your dial-up line call on your TC Login:!root Password:<your password> NetServer>MANAGE and you have CLI or contact me ICQ UIN 32213999 -- Using M2, Opera's revolutionary e-mail client: http://www.opera.com/m2/

1 0