October 2001 - USR-TC - mailman.xmission.com

RE: (usr-tc) NMC not responding
by Mark E. Levy 06 May '03

06 May '03

I;ve had this happen a few times. Just reboot the NMC card by sliding it out if the chassis or via the console interface and it will be well again (until next time). Rebooting the NMC won't affect active users sessions. --------------------------------------------------------------------- Mark E. Levy, President FSInet, Inc. | System Management Associates, Inc. 800-827-6085 x202 | 847-291-1550 x202 847-753-6832 fax | 847-291-3866 fax www.fsi.net | www.sysman-inc.com mark(a)fsi.net | levy(a)sysman-inc.com --------------------------------------------------------------------- > -----Original Message----- > From: Jeff Mcadams [mailto:jeffm@iglou.com] > Sent: Friday, June 08, 2001 9:51 AM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) NMC not responding > > > Also sprach Kirk Mitchell > > My NMC recently stopped responding to SNMP queries, etc and I'm > >unable to access it via TCM. It has, however, not seemed to affect > >anything as far as dial-up, routing, etc. Other than the fact that I > >can't run MRTG against it or the badmodems.pl script, there's no > >indication that it's having problems. > > Not surprising. The NMC does not have anything to do with the routine > actions of taking and handling calls...it is what it says it > is...purely > a management card. You can totally remove the NMC and not lose any of > the actual *production* functionality of the chassis. > > > Has the card gone bad...need replaced, lost something in part of > >config? How do I go about finding/fixing the problem? > > Proly just needs a reboot, or possibly a reconfig...I've had > a few lose > some of the config (including IP addresses and stuff), and a reconfig > from console (takes me about 30 seconds these days) gets them > fully back > up and running (sucks if its a remote city though). > -- > Jeff McAdams Email: jeffm(a)iglou.com > Head Network Administrator Voice: (502) 966-3848 > IgLou Internet Services (800) 436-4456 > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

(usr-tc) FW: [datacomm] Secret access to TCs
by Brian Becker 25 Jun '02

25 Jun '02

The newest edition to our IT Department (he's been in Tech Support for 3 years) emailed me this afternoon (full email below). I didn't believe him at first so I telneted to on of our TC boxes and when prompted with "Login:" I typed adm and pressed Enter. HOLY COW! It said "Hiper:" and I had full access. I'm curious as to how many people on this list were vulnerable like us (we have 20 TC boxes throughout Southeast Missouri). Brian Brian Becker President, Poplar Bluff Internet, Inc. P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114 Home of http://semo.net - Southeast Missouri's Online Community http://TotallyFabricated.com Total Scrutinizer - Tech Support Just Got Easier WebGabber - All-html Web Chat Software -----Original Message----- From: Adam Barnhill Sent: Tuesday, July 24, 2001 6:41 PM To: ---interoffice DataComm List--- Subject: [datacomm] Secret access to TCs It has come to my attention that our TCs were vulnerable to anyone's attack. User : adm Would allow access to manage and login to our TCs. The fix was easy. Just 'del user adm' and then 'save all' (thanx Brian) I was actually searching for TC command references, and happened upon ;) a hack list of default and backdoor passwords. The link I originally found a hack article on is http://the.wiretapped.net/security/info/textfiles/k1ine_11.txt and the password list is in that tree somewhere.. Lots of backdoors for other RAS, switches, hubs and other.. Adam Barnhill Systems Technician / IT Dept. Semo.net / Poplar Bluff Internet, Inc. 1(877)686-9114 http://semo.net/ _______________________________________________ datacomm mailing list datacomm(a)lists.semo.net http://lists.semo.net/mailman/listinfo/datacomm - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

(usr-tc) Upgraded TC's
by Mark Thornton 21 Jun '02

21 Jun '02

We jsut upgraded our TC chassis to the lastest available code (yes we paid for support) and the phones have stopped ringing. We always had a certain level of calls with various connection problems of one sort or another, but that seems to have dried up in the week since we installed the new code. We made the decision to go with the paid support over replacement of our chassis strictly on financial grounds. There was no way to amortize new equipment costs for our dialup market. Yes, it blows to have to pay for something others get for free, however I must say the support I have gotten is so much better than what I ever got from 3Com directly. There has been no backlash from the new code that I have found which is also a welcome change. Mark Thornton San Marcos Internet, Inc 512-393-5300 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

16 21

(usr-tc) Upgrading a TC
by Rob 19 Jan '02

19 Jan '02

What is the *least* expensive way to upgrade a TC v34 system to v90? Is there one? Feel free to write me offlist at mailto:rjb@worldnetoh.com. Thenks! Rob - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3

(usr-tc) hiperarc + freeradius woes
by jason 01 Nov '01

01 Nov '01

I'm not sure how active this list still is but here goes :: I'm having a strange problem with getting Framed-IP-Address to work with a HiperArc Total Control Unit. It seems that even though the Framed-IP-Address is set, it won't respect that and assigns a dynamic, when my freeradius server is in action. It works however when talking to the old Cistron server. The othe thing is that my good ole portmaster 2 works fine with either.. These hiperarcs seem to be finicky beasts and I imagine that either I'd not seeing something it wants or there is some configureation setting that we're not aware of that needs to be tweaked Here's a copy of what I recieve when I do a radtest to either server.. localhost is the freeradius and svr4 is the cistron. bash-2.05# ./radtest username(a)domain.net password localhost 5 testing123 Sending Access-Request of id 57 to 127.0.0.1:1645 User-Name = "username(a)domain.net" Password = "2\006\n\323\316\371G\3334`*\315\033\020I\010\355" NAS-IP-Address = radius1.egix.net NAS-Port-Id = "5" rad_recv: Access-Accept packet from host 127.0.0.1:1645, id=57, length=68 Service-Type = Framed-User Framed-Protocol = PPP Framed-MTU = 1500 Framed-Routing = None Framed-Compression = Van-Jacobson-TCP-IP Framed-IP-Address = 209.131.199.209 Framed-IP-Netmask = 255.255.255.255 Idle-Timeout = 0 bash-2.05# ./radtest username(a)domain.net password svr4.iei.net 5 testing123 Sending Access-Request of id 61 to 209.131.216.202:1645 User-Name = "username(a)domain.net" Password = "\241`s\307r\330rQQ\2244x\233\314\344\367\334" NAS-IP-Address = radius1.egix.net NAS-Port-Id = "5" rad_recv: Access-Accept packet from host 209.131.216.202:1645, id=61, length=68 Service-Type = Framed-User Framed-Protocol = PPP Framed-MTU = 1500 Framed-Routing = None Framed-Compression = Van-Jacobson-TCP-IP Framed-IP-Address = 209.131.199.209 Framed-IP-Netmask = 255.255.255.255 Idle-Timeout = 300 Any help or insight would be greatly appreciated. -jason - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 4

(usr-tc) Re: Harc code 30
by Dayton Internet 01 Nov '01

01 Nov '01

Sorry, I didnt change the subject on the previous email. ----------------------------- Has anyone found the definition of what causes the "30" disconnect reason supplied by the HyperArc from time to time? Or does anyones other radius have that defined in their dictionary? oct01:10/30/2001 17:23:08 ktaylor 204 TS4 261 66 13413 120663 User-Request "xxxxxxxxxx" oct01:10/30/2001 20:18:29 ktaylor 1498 TS4 275 121 144930 268281 User-Request "xxxxxxxxxx" oct01:10/31/2001 00:28:18 ktaylor 16 TS4 19 150 417 407 30 "xxxxxxxxxxx" ^^ || -- --Rich Adams, President-Dayton Internet Services, Dayton, Ohio-- --w8mfd(a)dayton.net--www.dayton.net--www.dayton.com--937-586-2500-- - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) WTB: USR MP16v34
by ISP-NetworkHardware.com 31 Oct '01

31 Oct '01

Anybody sitting on qty? I'll buy small packages but would love to find 10 at a shot. Please email me what you have available. MP16 v34 must be guaranteed working, I'll pay freight in. Also buy Cisco, Livingston, Ascend, Adtran, Kentrox to name a few. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2

(usr-tc) v90 firmware
by Scott Kupferschmidt 27 Oct '01

27 Oct '01

Hey guys. I need some help. I don't have a support contract with USR, but this is what I've got here. We have 2 USR Total Controls with 48 modems in each. The newer hardware of the two has older firmware for the modems not supporting V.90, but the SMC card has the feature code in it to support V.90. The older hardware has the V.90 firmware on the modems (so we swapped them from each chassis) and we're working on partial V.90. However, we'd like to get both of them all up to V.90 so we can utilize all of our ports once again. We have 1 PRI that is turned off because we cannot support it and we're having some config problems. I guess what I'm getting at here is.. I need to know where to get the firmware. Whether someone can email me it, or point me in the right direction on getting it -- that would be great. We are getting a lot of angry customers because of busy signals that we shouldnt be getting had we had the other TC up online accepting calls. Please help? Scott - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 5

Re: (usr-tc) What memory does the HiperARC use?
by Mike Greene 26 Oct '01

26 Oct '01

At 02:14 PM 10/16/01 -0400, you wrote: >Hi, >Does anyone know the specs on HiperARC memory? >I know it is EDO, but: >Parity or Non-Parity ? >Gold Lead or Tin Lead ? >5 volt ? 128MB EDO 168pin BUFFERED 3.3v Mine was tin lead, don't remember about parity though. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) Callback with HiperArc
by Erin Grooms 26 Oct '01

26 Oct '01

I've been trying to add a callback user with a static IP address to one of my hiperarcs, but have been having a couple of problems. I have a radius server as well, and I think it's skipping looking locally at all for the user. I get a basic authentication error when I try to dial-up (or telnet). Here is the basic config for the user I've got so far: INFORMATION FOR USER: callbacktest Status: INACTIVE Type: LOGIN NETWORK CALLBACK Expiration: NONE Message: this is a test DNIS Re Authentication: NO_REAUTH Special Xon Xoff Flow Control DISABLED Telnet Options: INVALID (D) Callback Type: STATIC Phone Number: "xxx-xxxx" Alternate Phone Number: (D) Input Filter: (D) Output Filter: (D) Modem Group: all (D) Session Timeout in seconds: 86400 Idle Timeout in seconds: 86400 Tap Status: DISABLED Tap Format: ASCII Tap Output: SYSLOG Tap Facility: LOG_AUTH Tap Loglevel: VERBOSE Port Limit: 2 Tap Address: 0.0.0.0 (D) Chat Script Name: PARAMETERS FOR LOGIN USERS: Login Service: TELNET TCP Port: 23 (D) Terminal: vt100 (D) Login Host Name: Login Host: 0.0.0.0 (D) Host Type: SELECT (D) PARAMETERS FOR NETWORK USERS: Network Service PPP Header Compression: TCPIP (D) Spoofing: DISABLED (D) MTU: 1514 (D) IP Usage: ENABLED (D) Address Selection: SPECIFIED Remote IP Address: 216.69.xxx.xx/H Next Hop Gateway IP Address: 0.0.0.0 (D) IP Routing: NONE (D) IP Routing Protocols: RIPV1 (D) IP RIP Routing Policies: IP RIP Authentication Key: Default Route Option: DISABLED (D) IGMP Query Interval: 125 seconds IGMP Max Response: 10 seconds IGMP Version: 2 IGMP Robustness: 2 IGMP Routing: DISABLED (D) Multicast Forwarding: DISABLED (D) Multicast Proxy: DISABLED (D) IPX Usage: ENABLED (D) IPX Address: 00000000 (D) IPX Routing: RESPOND (D) IPX WAN Usage: DISABLED (D) IPX RIP Update: 60 seconds IPX RIP Age Multiplier: 4 IPX SAP Update: 60 seconds IPX SAP Age Multiplier: 4 PARAMETERS FOR TUNNEL USERS: Tunnel Type: None (D) PARAMETERS for NETWORK PPP USERS Max Channels 2 (D) Channel Decrement Percent: 0 (D) Channel Expansion Percent: 0 (D) Expansion Algorithm: CONSTANT (D) Receive ACC Map: ffffffff (D) Transmit ACC Map: ffffffff (D) Compression Algorithm: AUTO (D) Compression Reset Mode: AUTO (D) Min Compression Size: 256 (D) Encryption Algorithm: NONE (D) Primary DNS Server: 216.69.xxx.xx Secondary DNS Server: 216.69.xxx.xx Periodic CHAP Timeout: 0 (D) Source Ip Address Filter: DISABLED (D) I'm mostly confused about the (D)'s everywhere, I haven't really dug very deep on my TCS boxes as far as adding extra users and such. Is there anything else I need to do on the user end, or on the hyperarc? I'm using version V4.2.32 of the firmware. Any help would be very appreciated. thanks! Erin Grooms System Administrator Erin Grooms System Administrator - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0