January 2001 - USR-TC - mailman.xmission.com

(usr-tc) Half the modems on DSP hanging up just after connection
by zip-usrtc＠ran.zipcon.net 19 Jan '01

19 Jan '01

I'm having an odd problem where a DSP card is dropping connections directly after the negotiation process finishes, but only on modems 1-12. Modems 13-23 work fine. When I enable modems 1-12, they always drop connections immediately after modem negotiation completes. I get this syslog message: ============ A call, call id = 720898, has arrived on interface slot:1/mod:12 A call is established, call id 720898, on interface slot:1/mod:12 The connection for call id 720898, on if slot:1/mod:12 was dropped for user UNKNOWN ============ The DSP card is a replacement from 3Com for a card that failed. The first replacement they sent did not work at all. I think this may also be a bad card, but am looking for tips on things to try. I have already restored all setting from default, saved it to NVRAM and rebooted the card many times. The fact that it does correctly answer calls on modems 13-23 makes me think its defective. I went into the DSP card console and ran chdev tslot X cmd tooserv soft where X is 1-12. Once that was done, all is fine (expect the card only has 11 active modems). I also notice that I am getting these syslog messages over and over. GWCMDM_AL, slot:1/mod:24 TAPI OPEN failed GWCMDM_AL, slot:1/mod:24 TAPI_OPEN failed, retrying Thanks for any tips, Dan - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) FS: USR Quad Bundles
by Steve Rivera -www.wrca.net 18 Jan '01

18 Jan '01

WR Communication has the following USR Total Control Hardware available: All flashed to current code. Qty's vary but I do have qty. $2500 or BO HD Chassis with 70A power NMC Netserver PRI 12x Quad Digital Modems v90 Dual PRI $3000 or BO HD Chassis with 70A Power NMC Netserver PRI 12x Analog/Digital Modems v90 Dual PRI Steve Rivera (VP) - 732.833.2111 x102 / CELL - 732.433.5890 - 24Hr URL: www.isp-networkhardware.com or http:///www.wrca.net Email: srivera(a)wrca.net - Mobile Email: srivera711(a)hotmail.com Worldwide Provider of Network Hardware Since 1981. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Re: multilink over multi-chassis'
by Steve Monkhouse 18 Jan '01

18 Jan '01

Thanks for the info mike.. One thing i obviously omitted to mention then.. what if both chassis' run Netservers and not ARC's...?? Steve - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 6

RE: (usr-tc) Multilink over multi-chassis'
by mstorjohann＠huntel.net 16 Jan '01

16 Jan '01

Steve: Here is information I received from this list on how to set this up on 2 or more HiperARCs. On ARC-A you would type: set mpip client_state on set mpip server_state on set mpip client (IP of ARC-A) sharedsecret <Secret on ARC-A> set mpip client (IP of ARC-B) sharedsecret <Secret on ARC-B> set mpip server (IP of ARC-A) sharedsecret <Secret for ARC-A> set ntp primary_server <IP of NTP server> enable ntp save all On ARC-B you would type: set mpip client_state on set mpip server (IP of ARC-A) sharedsecret <Secret for ARC-B> set ntp primary_server <IP of NTP server> enable ntp save all > Set ARC-A as mpip client + server, plus set it to an NTP server (know of > any good ones?). You don't need to worry about IP addresses of the different ARCs. The ARC will tunnel between each other so it is invisible to the client. Hope this helps. I can't remember who originally came up with this, but it was helpful for me. Mike Storjohann mstorjohann(a)huntel.net -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Steve Monkhouse Sent: Tuesday, January 16, 2001 4:28 PM To: usr-tc@lists. xmission. com Subject: (usr-tc) Multilink over multi-chassis' Has anyone solved the problem where a client who dials in multilink (ISDN or 56k) is issued modems from two different chassis' ? ( Which obviously then dont multilink ).. Is there any way of remedying this ? Steve - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Multilink over multi-chassis'
by Steve Monkhouse 16 Jan '01

16 Jan '01

Has anyone solved the problem where a client who dials in multilink (ISDN or 56k) is issued modems from two different chassis' ? ( Which obviously then dont multilink ).. Is there any way of remedying this ? Steve - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) ARC locking up?
by Steve Cobb 12 Jan '01

12 Jan '01

Can anyone tell me why when I use the HiperARC software version 1.2.6 software to modify something like users, it makes the ARC "lock up"? Some users can get on and there are green lights on the ARC but I can't telnet into it and most users cannot connect. Something wierd is happening. Any ideas? Thanks, Steve Cobb - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) RE: USR Total Control 70AMP DC Power Supplies
by Verreault, John 12 Jan '01

12 Jan '01

> For sale: USR Total Control 70AMP DC Power Supplies > > I have 6 slightly used ones available. > > Asking $200.00each or trade for 70 AMP AC power supplies > > John Verreault > AEI Internet > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Need expert SNMP consulting
by Brian Becker 10 Jan '01

10 Jan '01

Though we don't fit the bill because our software only helps once the user is connected, but I can't help but think our Total Scrutinizer will help you in a couple of ways. http://TotalScrutinizer.com Brian Becker President, Poplar Bluff Internet, Inc. (www.semo.net) Home of TotallyFabricated.com Software: Total Scrutinizer (www.TotalScrutinizer.com) - Tech Support Just Got Easier! WebGabber (www.WebGabber.com) - html-based Chat Software -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of eric(a)dol.net Sent: Tuesday, January 09, 2001 11:27 PM To: usr-tc(a)lists.xmission.com Subject: (usr-tc) Need expert SNMP consulting I have my checkbook out. We need some expertise in setting up a monitoring process for our quad modem / netserver boxes. We are well versed in using TCM to monitor and fix problems but we would like to know about them before the customers get pissed. In particular we have a pop with pots lines and 200 modems. We are always behind the times in diagnosing lines with no dialtone and static from the phone company and modems that just go bad. We don't want the end result to be labor intensive but something that informs us of problems that need to be resolved. The person responsible for the current process knows squat about perl so we need to speak and work with a person who can get this set up turnkey on one of our web servers for example. Help with an MRTG project would be an add on as well. thanks eric - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Need expert SNMP consulting
by eric＠dol.net 10 Jan '01

10 Jan '01

I have my checkbook out. We need some expertise in setting up a monitoring process for our quad modem / netserver boxes. We are well versed in using TCM to monitor and fix problems but we would like to know about them before the customers get pissed. In particular we have a pop with pots lines and 200 modems. We are always behind the times in diagnosing lines with no dialtone and static from the phone company and modems that just go bad. We don't want the end result to be labor intensive but something that informs us of problems that need to be resolved. The person responsible for the current process knows squat about perl so we need to speak and work with a person who can get this set up turnkey on one of our web servers for example. Help with an MRTG project would be an add on as well. thanks eric - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) DSP modems locking
by Steve Monkhouse 09 Jan '01

09 Jan '01

Strange one.. Ive got 2 x PRI channels on one of our DSP's that are not accepting calls. S1 & S17 ( so obviously not a pair ).. Whenever the you dial into them Ive tried software resetting them, and Ive even Hardware Reset the card, which also didnt fix it, So we physically pulled the DSP and reseated, still no go.. Ive moved the two modems to Local Out of Service for the interim, but how can i fix them. I Dont want to have to reflash the card.. but i suppose I can if i absolutely have to.. Any ideas ? Steve - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0