Re: M_Boats: Rigging questions
Dan, regarding your rigging question: "2. My 100% jib is at least 16" shy of the masthead when fully raised. I think my 150% may also fall short. I thought maybe this was because the mast was raked back too far--could that be? Did it shrink over the years? (It's old.) Is it the wrong size (though it appears to have been made especially for the boat)?" There are people on the list far more knowledgeable than I, but perhaps you have the "tall rig" on your early M17 Orli. The mast was taller by nearly two feet for that original rig, I think. Some on the list have deliberately converted to the tall rig for more sail area. Your sails could be raised higher by using a strop at the stem fitting, and you would even be able to see under them better as a result. Again, others have much better information than I do.Jerry, Bob, GO are possibilities. Even if you don't, you can try the strop (there is an exact nautical term for it, of course). David M17 #393
I used a SS wire with loops crimped at both ends. West Marine sells various length SS straps with holes every inch or so but it was a little too pricey for me compared to my Ace fix. Joe M17 651 ----- Original Message ----- From: "David C. Patterson" <davidcpatterson@msn.com> To: <montgomery_boats@mailman.xmission.com> Sent: Tuesday, May 05, 2009 1:02 PM Subject: Re: M_Boats: Rigging questions
Dan, regarding your rigging question:
"2. My 100% jib is at least 16" shy of the masthead when fully raised. I think my 150% may also fall short. I thought maybe this was because the mast was raked back too far--could that be? Did it shrink over the years? (It's
old.) Is it the wrong size (though it appears to have been made especially for the boat)?"
There are people on the list far more knowledgeable than I, but perhaps you have the "tall rig" on your early M17 Orli. The mast was taller by nearly two feet for that original rig, I think. Some on the list have deliberately converted to the tall rig for more sail area. Your sails could be raised higher by using a strop at the stem fitting, and you would even be able to see under them better as a result. Again, others have much better information than I do.Jerry, Bob, GO are possibilities. Even if you don't, you can try the strop (there is an exact nautical term for it, of course). David M17 #393
_______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
Remember, there is no privacy on the Internet!
If it's truly a 100% jib it's probably meant as an intermediate jib; for winds in the 20 kn area. You can raise it on a pennant, but it would raise the center of effort and the only real advantage would be to help keep the rig up if you were taking a couple of feet of green water over the bow, which is rare. jerry ----- Original Message ----- From: "David C. Patterson" <davidcpatterson@msn.com> To: <montgomery_boats@mailman.xmission.com> Sent: Tuesday, May 05, 2009 10:02 AM Subject: Re: M_Boats: Rigging questions
Dan, regarding your rigging question:
"2. My 100% jib is at least 16" shy of the masthead when fully raised. I think my 150% may also fall short. I thought maybe this was because the mast was raked back too far--could that be? Did it shrink over the years? (It's
old.) Is it the wrong size (though it appears to have been made especially for the boat)?"
There are people on the list far more knowledgeable than I, but perhaps you have the "tall rig" on your early M17 Orli. The mast was taller by nearly two feet for that original rig, I think. Some on the list have deliberately converted to the tall rig for more sail area. Your sails could be raised higher by using a strop at the stem fitting, and you would even be able to see under them better as a result. Again, others have much better information than I do.Jerry, Bob, GO are possibilities. Even if you don't, you can try the strop (there is an exact nautical term for it, of course). David M17 #393
_______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
Remember, there is no privacy on the Internet!
participants (3)
-
David C. Patterson -
jerry -
Joe Murphy