after removing the old tabernacle I decided to have the new halyard organizer plate welded to the new tabernacle plate and have the aft two holes enlarged and have the forward two holes enlarged, as well and drill them through both plates. The new plates are a bigger and better product. I think four holes are better than the three. They are at the machine shop now and should be ready soon. I purchased a uni-bit today at Home Depot for $ 17.95. Thank you, Bob, for the latest advise re: location of mast hole and filing at base of mast for easier set-up procedure. Rich Cottrell
Rich, When you drill a hole with the uni-bit, you can chamfer the hole by advancing the bit just a wee bit as if you were going to drill the next size up. I'm sure you will be cautious enough to learn to use it on a piece of scrap aluminum before you start working on the mast. Another tool that is useful is a spring loaded center punch so that you can mark the exact place you want to drill with an indentation where the drill can start to cut. Clarence Carpe Ventum ----- Original Message ----- From: "Richard Cottrell" <rc2222@pacbell.net> To: "Montgomery Boats" <montgomery_boats@mailman.Xmission.com> Sent: Wednesday, November 03, 2004 7:04 PM Subject: M_Boats: mast tabernacle
after removing the old tabernacle I decided to have the new halyard organizer plate welded to the new tabernacle plate and have the aft two holes enlarged and have the forward two holes enlarged, as well and drill them through both plates. The new plates are a bigger and better product. I think four holes are better than the three. They are at the machine shop now and should be ready soon.
I purchased a uni-bit today at Home Depot for $ 17.95.
Thank you, Bob, for the latest advise re: location of mast hole and filing at base of mast for easier set-up procedure.
Rich Cottrell
_______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
I used a Uni-bit made for cutting into the stainless steel bow pulpit to install the running lights on my M15. They work great but make sure the one you buy will handle stainless steel. I am hoping to be able to use the Uni-bit in a light weight bench drill press to "router" the slot in the old tabernackle to an open configuration like the new one. Thanks Doug Kelch "Seas the Day" --- Clarence Andrews <n9ca@comcast.net> wrote:
Rich,
When you drill a hole with the uni-bit, you can chamfer the hole by advancing the bit just a wee bit as if you were going to drill the next size up. I'm sure you will be cautious enough to learn to use it on a piece of scrap aluminum before you start working on the mast. Another tool that is useful is a spring loaded center punch so that you can mark the exact place you want to drill with an indentation where the drill can start to cut.
Clarence Carpe Ventum ----- Original Message ----- From: "Richard Cottrell" <rc2222@pacbell.net> To: "Montgomery Boats" <montgomery_boats@mailman.Xmission.com> Sent: Wednesday, November 03, 2004 7:04 PM Subject: M_Boats: mast tabernacle
after removing the old tabernacle I decided to have the new halyard organizer plate welded to the new tabernacle plate and have the aft two holes enlarged and have the forward two holes enlarged, as well and drill them through both plates. The new plates are a bigger and better product. I think four holes are better than the three. They are at the machine shop now and should be ready soon.
I purchased a uni-bit today at Home Depot for $ 17.95.
Thank you, Bob, for the latest advise re: location of mast hole and filing at base of mast for easier set-up procedure.
Rich Cottrell
_______________________________________________
http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
_______________________________________________
http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats
__________________________________ Do you Yahoo!? Check out the new Yahoo! Front Page. www.yahoo.com
participants (3)
-
Clarence Andrews -
Doug Kelch -
Richard Cottrell