4-Stroke Outboard, Break-In, Vibration
Hmmm..you could run the motor in a water barrel for a few hours before installing on your boat. I run my Seagulls that way every spring tuneup. After 3-4 hours of barrel running time, put it on your transom and motor around at varying speeds for a few more hours, and you should be OK. Harvey/ Ga M-17 Stargazer #294
Thanks, Harvey. I thought of the barrel approach and may use it: I was just afraid I'd have to do it for 10 hours! No one suggested ways to try to dampen outboard vibration: Does that mean no one suffers enough vibration to bother? Thanks, Craig ----- Original Message ----- From: "Harvey Wilson" <HarveyWilson@compuserve.com> To: <montgomery_boats@mailman.xmission.com> Sent: Thursday, February 20, 2003 8:35 PM Subject: 4-Stroke Outboard, Break-In, Vibration Hmmm..you could run the motor in a water barrel for a few hours before installing on your boat. I run my Seagulls that way every spring tuneup. After 3-4 hours of barrel running time, put it on your transom and motor around at varying speeds for a few more hours, and you should be OK. Harvey/ Ga M-17 Stargazer #294
Craig, Yes, The Honda 4 cycle 2 hp vibrates far slower and less than my old 2 cycle 2 hp evinrude. The 4 cycle has less rpm so the vibration is slower and the sound is deeper and less. It is a pleasure to use compared the my old noisy eggbeater. Doug Kelch "Seas The Day" --- Honshells <chonshell@ia4u.net> wrote:
Thanks, Harvey. I thought of the barrel approach and may use it: I was just afraid I'd have to do it for 10 hours! No one suggested ways to try to dampen outboard vibration: Does that mean no one suffers enough vibration to bother? Thanks, Craig
----- Original Message ----- From: "Harvey Wilson" <HarveyWilson@compuserve.com> To: <montgomery_boats@mailman.xmission.com> Sent: Thursday, February 20, 2003 8:35 PM Subject: 4-Stroke Outboard, Break-In, Vibration
Hmmm..you could run the motor in a water barrel for a few hours before installing on your boat.
I run my Seagulls that way every spring tuneup.
After 3-4 hours of barrel running time, put it on your transom and motor around at varying speeds for a few more hours, and you should be OK.
Harvey/ Ga
M-17 Stargazer #294
_______________________________________________
http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats __________________________________________________ Do you Yahoo!? Yahoo! Tax Center - forms, calculators, tips, more http://taxes.yahoo.com/
Hi Craig, I have a Honda 2 hp with the long shaft and I was a little disappointed the first time I took it out because of the noise and vibration. I think my problem was that after hearing so many good things about the Honda, I was expecting something closer to an electric. Previously I had owned an old Johnson 6 hp 2 cylinder that I swear was quieter and had less vibration. As I think some one else mentioned, single cylinders are inherently more vibration prone than multiple cylinders. . I have placed a piece of rubber backed carpeting on the motor mount and that helps a little but not too much. Now that I have been using the Honda for awhile I don't notice the noise and vibration as much. I haven't been going through any special 'break in" procedures but I do try and warm it up a minute or two before I leave the dock. As has been mentioned by others, it only takes about half throttle to to get out to where you want to put up the sails or even motor back in if there is no wind. Each time I am out I do try and use full throttle for a minute or two. All in all I think the Honda is a great little motor for the M15 and unless something else has come along since 2000 when I purchased mine, I would do it all over again. Don Olson M15 Phoenix, Az
Thanks, Don. --Craig ----- Original Message ----- From: "Don Olson" <don-keg@cox.net> To: <montgomery_boats@mailman.xmission.com> Sent: Friday, February 21, 2003 11:12 AM Subject: Vibration Hi Craig, I have a Honda 2 hp with the long shaft and I was a little disappointed the first time I took it out because of the noise and vibration. I think my problem was that after hearing so many good things about the Honda, I was expecting something closer to an electric. Previously I had owned an old Johnson 6 hp 2 cylinder that I swear was quieter and had less vibration. As I think some one else mentioned, single cylinders are inherently more vibration prone than multiple cylinders. . I have placed a piece of rubber backed carpeting on the motor mount and that helps a little but not too much. Now that I have been using the Honda for awhile I don't notice the noise and vibration as much. I haven't been going through any special 'break in" procedures but I do try and warm it up a minute or two before I leave the dock. As has been mentioned by others, it only takes about half throttle to to get out to where you want to put up the sails or even motor back in if there is no wind. Each time I am out I do try and use full throttle for a minute or two. All in all I think the Honda is a great little motor for the M15 and unless something else has come along since 2000 when I purchased mine, I would do it all over again. Don Olson M15 Phoenix, Az
participants (4)
-
Don Olson -
Doug Kelch -
Harvey Wilson -
Honshells