15 Jan
2014
15 Jan
'14
9:49 p.m.
I haven't taken the residue off yet, Thomas, but I'll be doing that soon. I'm sizing the cleat down as I've adopted a 1/4 low stretch line for the jib halyard. The exiting large cleat, though not in bad shape, allowed the halyard to slip a bit under hard use. Because I have a phobia about drilling holes in my boat, I'm going to fashion a cleat pedestal that will allow me to use the existing holes, and change the angle of the lead a bit to improve line capture. I'll keep you posted. t t _/\_ On Wed, Jan 15, 2014 at 12:02 PM, Thomas Buzzi <thomaspbuzzi@gmail.com>wrote: > Will you try "Goo gone" to get off the residue or did the thing come off > cleanly? > > > On Wed, Jan 15, 2014 at 11:04 AM, Tom Smith <openboatt@gmail.com> wrote: > > > To report back, I used a combination of my trusty Milwaukee heat gun > plus a > > stiff putty knife to remove this cleat. Worked well. Once I got the > knife > > started at the end, I simply heated the blade and made slow progress > until > > the cleat popped off. Thanks for the tips sailors. t > > > > > > > > t _/\_ > > > > > > On Tue, Jan 14, 2014 at 4:16 PM, Tom Smith <openboatt@gmail.com> wrote: > > > > > Good idea. Now where did I put that old stratocaster? > > > > > > I don't think it's 5200, thank goodness. t > > > > > > > > > > > > t _/\_ > > > > > > > > > On Tue, Jan 14, 2014 at 1:55 PM, <swwheatley@comcast.net> wrote: > > > > > >> One old trick is to take a thin guitar string and use it to "saw" back > > >> and forth under the fitting. Also, is there any chance someone bedded > > the > > >> cleat with 3M 5200? In that case, trying to pry it off almost > certainly > > >> will damage the deck. I avoid that stuff like the plague but I > > understand > > >> someone does sell a solvent for it. > > >> > > >> ----- Original Message ----- > > >> > > >> From: "Tom Smith" <openboatt@gmail.com> > > >> To: "For and about Montgomery Sailboats" < > > >> montgomery_boats@mailman.xmission.com> > > >> Sent: Tuesday, January 14, 2014 2:49:49 PM > > >> Subject: Re: M_Boats: Removing stubborn clamcleat > > >> > > >> Thanks Gary. I like the many solutions approach--I don't have to make > a > > >> decision that way. And yes, heat + solvent could very well lead to too > > >> much adventure... t > > >> > > >> > > >> > > >> t _/\_ > > >> > > >> > > >> On Tue, Jan 14, 2014 at 11:35 AM, <GILASAILR@aol.com> wrote: > > >> > > >> > Tom, > > >> > > > >> > Don't apply heat and solvent at same time - more contemplation has > > >> occurred > > >> > - we think that may have negative effects unless your insurance > > coverage > > >> > is exceptional. > > >> > > > >> > GO duh > > >> > > > >> > > > >> > In a message dated 1/14/2014 12:32:42 P.M. US Mountain Standard > Time, > > >> > GILASAILR@aol.com writes: > > >> > > > >> > Tom, > > >> > > > >> > A little solvent of your choice -lacquer thinner, acetone helps - my > > >> genoa > > >> > > > >> > camcleat was 'grown on' and that helped - heat helps -we have that > in > > >> > abundance down here- left a lot of residue - dark brown bedding > > compnd - > > >> > used > > >> > everything in the quiver - finally a brass brush & acetone + an > exacto > > >> > knife > > >> > blade (#7) to clean out the last bits - lotsa contemplative time > > whilst > > >> > scraping and pondering the real meaning of life. After that exercise > > - I > > >> > had > > >> > it ALL figgered out - I am a self actualized boat grunt! > > >> > > > >> > Give it hell! > > >> > GO - > > >> > going racing agin the big guns this weekend! 2014 WICR/Potter > > >> > Invitational > > >> > > > >> > > > >> > In a message dated 1/14/2014 11:04:03 A.M. US Mountain Standard > Time, > > >> > jerry@jerrymontgomery.org writes: > > >> > > > >> > Tom- I don't know of a sure cure, but if you made a little, sharp, > > >> > hardwood > > >> > wedge and just got it started, then tapping it in more as the cleat > > >> > loosened > > >> > up, it would probably work, I've done that before with no problems. > > >> > > > >> > It's probably just frozen on! > > >> > > > >> > jerry > > >> > ----- Original Message ----- > > >> > From: "Tom Smith" <openboatt@gmail.com> > > >> > To: "For and about Montgomery Sailboats" > > >> > <montgomery_boats@mailman.xmission.com> > > >> > Sent: Tuesday, January 14, 2014 8:58 AM > > >> > Subject: M_Boats: Removing stubborn clamcleat > > >> > > > >> > > > >> > > I'm changing out the foresail halyard clamcleat on the cabin-top > of > > my > > >> > > M17. Man, that baby is on there. Removed the bolts/nuts, but she > no > > >> > want > > >> > > to move. I hesitate to pry because it's so well seated I'm afraid > a > > >> > chunk > > >> > > of 'glass will come up too. > > >> > > > > >> > > Any suggestions on how to get this thing loosened up? The careful > > >> > > application of heat? Some kind of solvent? > > >> > > > > >> > > Suggestions appreciated. Tom > > >> > > > > >> > > > > >> > > t _/\_ > > >> > > > > >> > > > >> > > > >> > -- > > >> > I am using the free version of SPAMfighter. > > >> > SPAMfighter has removed 9866 of my spam emails to date. > > >> > Get the free SPAMfighter here: http://www.spamfighter.com/len > > >> > > > >> > Do you have a slow PC? Try a Free scan > > >> > http://www.spamfighter.com/SLOW-PCfighter?cid=sigen > > >> > > > >> > > > >> > > > >> > > > >> > > > >> > > > >> > > >> > > > > > >