Hmmm.... I'll have to check later to see about the alignment with the compression post. The boat is still under winter cover right now. The tabernacle is mounted as you observed, with the slot slightly forward. I have had it off the boat, but it was obvious which way it was to go back on as the shape of the foot of the mast was clearly etched into the surface of the tabernacle where it sits. On Tue, Apr 24, 2018 at 6:57 PM, John Schinnerer <john@eco-living.net> wrote:
Same pic, different thread - I notice that your boat has what appears to be the same mast step as mine - tall stainless "U" with slot running vertically, off center fore-aft, for the bolt.
However yours is 180 degrees from mine - on yours, the slot is more towards the bow. On mine it is more towards the stern.
On mine, as it is, the mast base is directly over the compression post. The part of the step forward of the mast is also forward of the post.
So if I turned my step 180 to look like yours, using the same holes, the base of mast would be a bit offset forward of the post (partly forward of the post). I assume this would be a bad idea and the mast base should be directly atop compression post. Is your mast base directly atop compression post?
Just makes me curious about variations in production...why would the slot in the step be off-center fore-aft anyhow? Which way around is "correct" or does it matter, as long as mast base is directly atop compression post?
cheers, John S.
On 04/24/2018 05:41 PM, Larry Yake wrote:
Here's a picture of my layout on CornDog. I routed it tight along the toe rail so it's not underfoot. Works very well. Perhaps not clear in the picture is that there is a fairlead on the pulpit which guides the line directly into the furler. Small blocks guide it along the toe rail, and it is cleated in a cam cleat on top of the coaming.
On Tue, Apr 24, 2018 at 5:05 PM, George Iemmolo <griemmolo2@gmail.com> wrote:
John
Mine is outboard on the edge of the cabin top where there is a slight crease. for the line to lay in.
George "We Can Not Control the Wind But We Can Adjust Our Sails"
On Tue, Apr 24, 2018 at 4:31 PM, John Schinnerer <john@eco-living.net> wrote:
Thanks George & others who replied...I was contemplating a similar
routing
I think. Quick question, in absence of pics:
Do your furling lines run outboard, or inboard, of the cabin-top handrail (assuming you have one)?
thanks, John S.
On 04/24/2018 02:19 PM, George Iemmolo wrote:
John
Just pulled my M15 out of the garage to get it ready for splash mid May and noticed that I had used 4 eye straps to lead the furling line aft. I forgot the one just ahead of the jam cleat on the starboard side cabin roof.
George 96 M15 #602 Merry Helen II
George "We Can Not Control the Wind But We Can Adjust Our Sails"
On Tue, Apr 24, 2018 at 9:06 AM, Randy Sommerfeld < sommerfeldrandy@gmail.com
wrote:
Maybe I should explain that I have had 2 two M17, first one was a 1979
which did not have a roller furling. My current M17 which I purchased new from Bob in 2010 and put on the roller furling. Both boats were named
No
Worries, I am not very creative.
I bought my first M17 from Crows Nest yachts in Woodbury MN in the
early
1990’s, sailed on Lake Menomin, Lake Pepin and once on Lake Superior.
Moved on to bigger boats, but missed it, so told myself that if I can ever afford to buy a nother one I would. So in 2009 I ordered it and drove out to California and pulled it back to Wisconsin in August of 2010,
pictured
below
That would be awesome to see my first M17 again, a of lot fond memories sailing with the family.
Sent from Mail for Windows 10
From: Dan Farrell Sent: Tuesday, April 24, 2018 8:38 AM To: Msog List Subject: Re: M_Boats: Jib furling line routing on M17
Randy,
If you since sold no worries, I probably own her now; that's still her name and the fairleads are mostly still in place, though the roller furling has since been removed.
If that was your boat, I'd love to hear any history you may be able to share. I'm curious about her history.
Or maybe just a coincidence?
Dan Farrell M17 #301
Randy Sommerfeld <sommerfeldrandy@gmail.com> wrote:
On my M17, I did it just like George did, except I did it on the port
> > side, using eye straps to keep things going in the right direction. I used a small pulley, (block) by the furling unit so the line would not bind
on
anything. No problems.
Randy Sommerfeld > No Worries > > Sent from Mail for Windows 10 > > From: George Iemmolo > Sent: Monday, April 23, 2018 4:53 PM > To: For and about Montgomery Sailboats > Subject: Re: M_Boats: Jib furling line routing on M17 > > John > On my M15 I routed the furling line down the starboard side of the > deck
up
> along the edge of the cabin and along its top in the cabin crease to > a > jam > cleat at the end of the cabin top. I used 3 small eye straps to > assist > the > line in it's journey. Be sure to place the first one so that the > furling
line is perpendicular to the forestay to prevent it jamming in the
> fuller This keeps it out of the way of the main halyard that is led > aft
also.
> > George > "We Can Not Control the Wind > But We Can Adjust Our Sails" > > On Mon, Apr 23, 2018 at 12:43 PM, John Schinnerer < > john@eco-living.net>
wrote:
> > Hi all, > >> >> Those of you with a furling jib on your M17 - where/how did you >> route >> >> your >
furling line? Pictures appreciate if available. > >> >> And, how happy are you with it, would you change anything that would >> >> make >
it better (more convenient, simpler, less likely to foul/snag/trip > over,
etc.).
>> >> thanks, >> John >> >> >> -- >> John Schinnerer - M.A., Whole Systems Design >> -------------------------------------------- >> - Eco-Living - >> Whole Systems Design Services >> People - Place - Learning - Integration >> john@eco-living.net - 510.982.1334 >> http://eco-living.net >> http://sociocracyconsulting.com >> >> >> >> >
-- John Schinnerer - M.A., Whole Systems Design
- Eco-Living - Whole Systems Design Services People - Place - Learning - Integration john@eco-living.net - 510.982.1334 http://eco-living.net http://sociocracyconsulting.com
-- John Schinnerer - M.A., Whole Systems Design
- Eco-Living - Whole Systems Design Services People - Place - Learning - Integration john@eco-living.net - 510.982.1334 http://eco-living.net http://sociocracyconsulting.com